Rémi KokabiNovember 19, 20265 min read

How many touches does it take to book a meeting? lemlist data

312 touches to book one meeting with email alone. 118 if you add LinkedIn and calls. 41 for the top 10% of campaigns. That gap is the real cost of outbound, measured one send at a time.

Most reps ask how many emails to book a meeting without ever counting the full sequence behind the reply. A touch is an email sent, a LinkedIn message delivered, or a call connected. Add them up and divide by meetings booked, and you get a number that exposes exactly how much effort your team burns per conversation.

I’ll walk through what lemlist’s own campaign data says about that number, why multichannel sequences cut it by more than half, and the four levers that pull it down further. Then I’ll show how to turn it into a capacity plan, so you know how many reps and how many touches it takes to hit next quarter’s meeting target.

Touches per meeting, the metric that sums up everything

Reply rate tells you how often people respond. It says nothing about whether those replies turned into meetings, or how many messages you burned to get there. Touches per meeting captures the full picture in a single number.

The formula is simple. Divide the total touches your campaign sent by the number of meetings booked. The lower the number, the less effort wasted per conversation. That makes it the most honest efficiency metric an outbound team can track, and a better planning input than reply rate alone. If you want a deeper look at the metrics that matter for outbound reps, start there.

What lemlist data shows

The table below comes from 586,310 campaigns run by 52,000 teams between October 2025 and November 2026, covering 412.6M messages and 1.9M calls across all markets.

Campaign type

Touches per meeting booked

Email-only campaigns

312

Multichannel campaigns

118

Top 10% of campaigns

41

Source: lemlist internal data from its users.

The gap between 312 and 41 is not marginal. The best-performing campaigns book a meeting with roughly one-eighth the effort of an average email-only sequence. That gap comes down to who you contact, how you reach them, and when you stop.

Why multichannel campaigns need fewer touches

Each channel carries a different reply rate, and campaigns that combine channels see the highest rates overall.

Channel mix

Reply rate (all markets)

Email only

2.4%

LinkedIn only

6.6%

Email + LinkedIn

7.1%

Source: lemlist internal data from its users.

Campaigns using email and LinkedIn together reply at 7.1%, compared to 2.4% for email alone. Campaigns using LinkedIn on its own reply at 6.6%. When you layer channels, each touch has a higher probability of generating a reply, so you need fewer total touches to reach a meeting.

This is a correlation, not a guarantee. Teams that run multichannel outreach tend to be more deliberate about targeting and copy, which also contributes to the lower number. But the channel data is consistent: more relevant touchpoints across surfaces means fewer wasted sends.

4 levers to lower your number

Smaller lists

In the European market, campaigns targeting 10 to 49 leads reply at 8.45%. Campaigns targeting 1,000+ leads reply at 2.60%. Smaller lists force better targeting. When every lead on the list fits your ICP, fewer touches go to people who were never going to respond.

Start from a signal

Lists built from buying signals outperform everything else. In Europe, signal-based lists reply at 14.6% compared to 4.4% for all other lists. In the US, the gap is wider: signal-based lists reply at 17.1% versus 3.0% for all other lists. A signal (a funding round, a job change, a tech stack shift) gives you a reason to reach out and gives the prospect a reason to care.

Add LinkedIn and a warm call

A warm call placed after a LinkedIn connection accept connects at 21.4%, compared to 9.6% for a cold first-touch call. The LinkedIn step creates recognition. The call converts that recognition into a conversation. Stacking these two steps after an email sequence compounds the effect of each touch, which is why multichannel campaigns land at 118 touches per meeting instead of 312.

Stop after the right number of steps

More steps do not always mean more meetings. The top 10% of campaigns reach 41 touches per meeting, and they do it with tight sequences that stop when engagement drops off. Adding extra emails to a sequence that lost momentum inflates your denominator. Review step-level data, cut what produces no replies, and keep sequences short enough that every touch earns its place.

Use it to plan capacity

Once you know your touches-per-meeting number, you can work backward from a meeting target to a headcount plan.

Pick your monthly meeting goal. Multiply it by your touches-per-meeting number to get the total touches required. Then divide by the number of touches each rep can send per month across email, LinkedIn, and calls. The result is the number of reps you need.

A team running multichannel campaigns at 118 touches per meeting needs far fewer total touches than one stuck at 312. And a team performing closer to the top 10% at 41 touches per meeting can hit the same meeting target with a fraction of the headcount.

This is the math that turns an efficiency metric into a staffing and budgeting decision. For a full walkthrough of how to connect touches to pipeline dollars, see the guide on outbound pipeline math. And if you are building next quarter’s plan around these numbers, the Q1 pipeline planning framework walks through the process step by step.

Final takeaway

Your touches-per-meeting number tells you exactly where your outbound motion is efficient and where it leaks effort. Measure it now, then pull the levers that bring it down: tighter lists, signal-based timing, and a multichannel sequence that gives every touch a reason to exist.

Build your first signal-based sequence in lemlist.

Reach prospects everywhere

Combine email, LinkedIn, and calls to book more meetings.

Frequently asked questions

Across all markets, email-only campaigns average 312 touches per meeting booked. That number drops to 118 when you add LinkedIn and calls, and the top 10% of campaigns book a meeting every 41 touches. The answer depends on your list quality, copy, and channel mix.

A touch is any outbound action delivered to a prospect. Emails sent, LinkedIn messages delivered, and calls connected all count. Profile visits or internal tasks do not.

The opposite. Multichannel campaigns need 118 touches per meeting compared to 312 for email-only campaigns. Each touch is more likely to generate a reply, so you send fewer total messages to reach the same outcome. The setup takes more thought upfront, but the per-meeting cost in effort is lower.

Divide total touches sent (emails, LinkedIn messages, connected calls) by meetings booked in the same period. Track it weekly or monthly per rep and per campaign. A rising number means your targeting or copy is slipping. A falling number means your changes are working.
Rémi Kokabi

Rémi Kokabi

Co-founder @GTM Club

Share this post